Primers & Fittings

1/4 NPT x 3/8 Barb 90-Degree Brass Elbow Fitting. Used on Blowsion Fuel Tank.

Part Number: 01-01-078

The 1/4" Quick Disconnect / Fuel Restrictor can be used as fuel line quick disconnect and/or for fuel restriction. Pre-tapped and threaded to accept Mikuni Main Jet (Jets not included). Includes stainless steel hose clamps. Now Available in all colors!

This cool universal anodized black aluminum mounting plate allows easy mounting of the rotary bilge switch as well as primer bulb on the dash. Specifically designed for the SXR but will work with other models. Inside mounting with the correct bulb style primer hole and rotary bilge switch ID means a sanitary install in minutes with no grinders or tubes of silicone needed.

Part Number: 04-06-002

Finish the look of your engine compartment with Blowsion specialty colored 1/4" fuel hose. Available in Clear, Blue, Green, Orange, Red, Yellow, or Black. Quantity is sold by the foot in continuous lengths.

Finish the look of your engine compartment with Blowsion specialty colored 1/8" fuel primer hose. Available in Clear, Blue, Green, Orange, Red, Yellow, or Black. Quantity is sold by the foot.

Blowsion Fuel Tank Fitting with Rubber Grommet. 1/4 Hose Barb. Compression Fit. Install with 17/32 Drill Bit.

Part Number: 01-02-598

Universal Fuel Pickup Filter. Add some of these for extra fuel filtration and also keeps the fuel in your lines when going upside down.

Part Number: 01-02-449

Mikuni high and low-speed carburetor adjuster screws with "T" cross bar - extended length for easy adjustments. Absolutely a must when running aftermarket pipes.

Part Number: 01-02-540

Oil block-off plates allow for an easy conversion from factory oil injection to pre-mixing your own fuel. Block-off plates fit all Yamaha 650701/760 and Kawasaki 650/750 Models. Hardware included. Anodized Black.

Part Number: 01-03-812

Try the sanitary "non foot destroying" rubber-based bulb type primer. In stock and ready to flow! Pair with the Blowsion Dash Fitting for best protection.

Part Number: 01-02-411

Fits 8mm choke shaft Keihin dual carburetor. Starting the engine of your personal watercraft is never a problem with a Blowsion primer kit. All brass fittings and Primer Bulb Get rid of that worthless factory choke and apply a direct shot of fuel! Pair with the Blowsion Dash Fitting for best protection.

Part Number: 01-02-408

Fits 8mm choke shaft Keihin single carburetors. Starting the engine of your personal watercraft is never a problem with a Blowsion primer kit. All brass fittings and Primer Bulb. Get rid of that worthless factory choke and apply a direct shot of fuel! Pair with the Blowsion Dash Fitting for best protection.

Part Number: 01-02-407

Fits 6mm choke shaft Mikuni dual carburetors. Starting the engine of your personal watercraft is never a problem with a Blowsion primer kit. All brass fittings and Primer Bulb. Get rid of that worthless factory choke and apply a direct shot of fuel! Pair with the Blowsion Dash Fitting for best protection.

Part Number: 01-02-406

Fits 6mm choke shaft Mikuni single carburetor. Starting the engine of your personal watercraft is never a problem with a Blowsion primer kit. All brass fittings and Primer Bulb. Get rid of that worthless factory choke and apply a direct shot of fuel! Pair with the Blowsion Dash Fitting for best protection.

Part Number: 01-02-405

Fits 8mm choke shaft Keihin dual carburetor. Starting the engine of your personal watercraft is never a problem with a Blowsion primer kit. All brass fittings and bulletproof plunger. Get rid of that worthless factory choke and apply a direct shot of fuel!

Part Number: 01-02-404