Hull Components

Blowsion 45-Degree machined aluminum bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Anodized Black or Clear.

Blowsion machined aluminum 3/4 inch bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Clear, Black, Green, Red, Blue, Orange and Purple anodized colors.

Blowsion machined aluminum straight bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Clear, Black, Green, Red, Blue & Orange anodized colors.

Rule Non-Automatic 500GPH Fully Submersible 12 Volt DC bilge pump. Unmatched in pumping power and longevity. Higher Flow – optimized impeller to provide greater flow at the same amperage. Back Flow Prevention - reduces the amount of water left over in the bilge, reducing odor and helping keep your bilge cleaner. Easy to mount and ready to go!

Part Number: 06-01-001

Rule 25SA Fully Submersible Bilge Pump, 500 Gallon Per Hour, 12 Volt DC, Automatic Electronic Sensing. Bilge Pump turns on and checks for water approximately every 2-1/2 minutes. If resistance (water) is found, it will run for as long as water is present. When all the water is pumped out, the pump shuts off and returns to its 2-1/2 minute test cycle.

Part Number: 06-01-002

Blowsion Bilge Pump Hose - 10 Foot Section is plenty for most dual pump and custom applications. Color: Black Only. Hose Diameter (ID): 3/4" inch.

Part Number: 06-01-302

Blowsion Bilge Pump Hose - 3 Foot Section is plenty for most single pump applications. Color: Black Only. Hose Diameter (ID): 3/4" inch.

Part Number: 06-01-301

Universal Handle Bar Mount Bilge Switch. Fits any watercraft handle bars on the market. Anodized Black.

Part Number: 06-01-212

Blowsion Bilge Switch Stop / Start Switch Mount - Yamaha. This sano billet switch assembly mounts directly to the bottom of the OEM Start / Stop switch housing of all Yamaha watercraft.

Part Number: 06-01-214

Finally- a replacement switch and 9 feet of cable for the always popular handlebar mount switches.

Part Number: 06-01-215

Sanitary anodized and engraved Blowsion logo carburetor block off. A necessity when using a remote fuel pump. Fits all Mikuni carbs. Billet aluminum with all stainless hardware included.

Part Number: 01-02-557

Blowsion 8mm Billet Conical Washers. Replace the brittle and breakable plastic nylon washers that are included with Rickter and many aftermarket hulls. Available in all Colors!

Replace your rear factory hood latch with a billet aluminum BLOWSION latch and ride worry free. Recently updated and re-machined to also fit the Kawasaki SXR 800 and SXR 1500. Also fits all years Yamaha FX1 and all years Yamaha Super Jet. A must for surf and big wave riders, especially those running a BLOWSION pole limiting rope. Requires the stock base locking hardware. Now available in more colors- Anodized Green, Red, Blue, Orange, Clear, Purple and Black!

NEW! - The Blowsion Billet Strap Hook. Replaces OEM Yamaha style waterbox, battery, and fuel tank strap hooks. Fits ALL years Yamaha Superjet, Rickter Hulls, Lightweight.DE, and many other aftermarket superjet based hull types. The Blowsion Strap Hook incorporates a removable 3mm set screw that retains the strap in place so that it cannot come off. This innovative little feature works perfectly for the hard to reach strap hooks where the straps have a tendency to come off. Price includes one hook, one M6 x 16mm bolt and a M3 x 6mm bolt. Available in Purple, Red, Black, Green, Orange, Blue and Teal Anodized Colors.

Our new CAS (cool as S*%!) flow valve design prevents water getting in during tail stands, wave jumping, or all out buoy shredding. The new billet flange assembly allows use of our billet exhaust outlet so vain riders can sanitize both sides of the rear of their ski. Fits all years Yamaha Superjet, Kawasaki 650, Kawasaki 750, Kawasaki SXR 800, Polaris Octane, Rickter XFS, Rickter XFR, Rickter EVO, Rickter Edge and Most Aftermarket Hulls.

Part Number: 06-01-022