Hull Components

Blowsion 45-Degree machined aluminum bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Anodized Black or Clear.

Blowsion machined aluminum 3/4 inch bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Clear, Black, Green, Red, Blue, Orange and Purple anodized colors.

Blowsion machined aluminum straight bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Clear, Black, Green, Red, Blue & Orange anodized colors.

Rule Non-Automatic 500GPH Fully Submersible 12 Volt DC bilge pump. Unmatched in pumping power and longevity. Higher Flow – optimized impeller to provide greater flow at the same amperage. Back Flow Prevention - reduces the amount of water left over in the bilge, reducing odor and helping keep your bilge cleaner. Easy to mount and ready to go!

Part Number: 06-01-001

Rule 25SA Fully Submersible Bilge Pump, 500 Gallon Per Hour, 12 Volt DC, Automatic Electronic Sensing. Bilge Pump turns on and checks for water approximately every 2-1/2 minutes. If resistance (water) is found, it will run for as long as water is present. When all the water is pumped out, the pump shuts off and returns to its 2-1/2 minute test cycle.

Part Number: 06-01-002

Blowsion Dual Bilge Pump Mounting Bracket. The bracket locates the pump within millimeters from the base of the Super Jet hull. Easy built in installation, no messy adhesives. Fits 1994 and up Yamaha Superjet Models. All hardware included. Material: Aluminum. Color: Anodized Black.

Part Number: 06-01-153

Blowsion Bilge Pump Hose - 10 Foot Section is plenty for most dual pump and custom applications. Color: Black Only. Hose Diameter (ID): 3/4" inch.

Part Number: 06-01-302

Blowsion Bilge Pump Hose - 3 Foot Section is plenty for most single pump applications. Color: Black Only. Hose Diameter (ID): 3/4" inch.

Part Number: 06-01-301

Single bilge pump mounting bracket for all 1994 and newer Yamaha SuperJet Models. The bracket locates the bilge pump within millimeters from the base of the Super Jet hull. Easy built in installation, no messy adhesives. All hardware included. Material: Aluminum. Color: Anodized Black.

Part Number: 06-01-152

Universal Handle Bar Mount Bilge Switch. Fits any watercraft handle bars on the market. Anodized Black.

Part Number: 06-01-212

Blowsion Bilge Switch Stop / Start Switch Mount - Yamaha. This sano billet switch assembly mounts directly to the bottom of the OEM Start / Stop switch housing of all Yamaha watercraft.

Part Number: 06-01-214

Finally- a replacement switch and 9 feet of cable for the always popular handlebar mount switches.

Part Number: 06-01-215

Sanitary anodized and engraved Blowsion logo carburetor block off. A necessity when using a remote fuel pump. Fits all Mikuni carbs. Billet aluminum with all stainless hardware included.

Part Number: 01-02-557

Blowsion Billet Choke Knob. Direct replacement for YAMAHA OEM Plastic choke knob. Installs with OEM set screw (Not Included). Fits all Years Yamaha Superjet, FX1 and WaveBlaster Models. Bright Dip Anodized Black.

Part Number: 04-03-351

Sanitize the dash of your Yamaha controls with this Blowsion Billet Dash Knob. Replaces the OEM Yamaha plastic ON/OFF/RESERVE Knob. Uses OEM screw to mount. Fits all years Yamaha Superjet, FX1 and WaveBlaster Models. Also Compatible with most Yamaha 2-Stroke Sitdown Models (Wave Jammer, Wave Runner, Wave Raider, VXR). Bright Dip Anodized Black. 1 Per Package.

Part Number: 04-03-352