Hull Components

Hull Components

Items 1 to 16 of 63 total

per page

Page:
  1. 1
  2. 2
  3. 3
  4. 4
  • Bilge Fitting 45-Degree

    Blowsion 45-Degree machined aluminum bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Anodized Black or Clear.

    Learn More
    $21.95

  • Bilge Fitting Pro

    Blowsion machined aluminum 3/4 inch bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Clear, Black, Green, Red, Blue, Orange and Purple anodized colors.

    Learn More
    $21.95

  • Bilge Fitting Straight

    Blowsion machined aluminum straight bilge fittings are a clean replacement of the bulky plastic fittings usually supplied with aftermarket bilge pump kits. Available in Clear, Black, Green, Red, Blue & Orange anodized colors.

    Learn More
    $17.95

  • Bilge Pump - Rule - 500GPH

    Rule Non-Automatic 500GPH Fully Submersible 12 Volt DC bilge pump. Unmatched in pumping power and longevity. Higher Flow – optimized impeller to provide greater flow at the same amperage. Back Flow Prevention - reduces the amount of water left over in the bilge, reducing odor and helping keep your bilge cleaner. Easy to mount and ready to go!

    Part Number: 06-01-001

    Learn More
    $34.95

  • Bilge Pump - Rule - 500GPH Automatic

    Rule 25SA Fully Submersible Bilge Pump, 500 Gallon Per Hour, 12 Volt DC, Automatic Electronic Sensing. Bilge Pump turns on and checks for water approximately every 2-1/2 minutes. If resistance (water) is found, it will run for as long as water is present. When all the water is pumped out, the pump shuts off and returns to its 2-1/2 minute test cycle.

    Part Number: 06-01-002

    Learn More
    $99.99

  • Bilge Pump Hose - 10FT

    Blowsion Bilge Pump Hose - 10 Foot Section is plenty for most dual pump and custom applications. Color: Black Only. Hose Diameter (ID): 3/4" inch.

    Part Number: 06-01-302

    Learn More
    $23.00

  • Bilge Pump Hose - 3FT

    Blowsion Bilge Pump Hose - 3 Foot Section is plenty for most single pump applications. Color: Black Only. Hose Diameter (ID): 3/4" inch.

    Part Number: 06-01-301

    Learn More
    $7.00

  • Bilge Switch - Handlebar Mount - Universal

    Universal Handle Bar Mount Bilge Switch. Fits any watercraft handle bars on the market. Anodized Black.

    Part Number: 06-01-212

    Learn More
    $99.95

  • Bilge Switch Replacement - 9ft Wire

    Finally- a replacement switch and 9 feet of cable for the always popular handlebar mount switches.

    Part Number: 06-01-215

    Learn More
    $77.95

  • Blowsion Billet Fuel Cap - Yamaha

    Blowsion Low Pro Billet aluminum fuel caps for all Yamaha watercraft. Low profile smooth design allows for outside fueling, yet will not get in the way during aerial or freestyle moves around the front of the watercraft. Available in all anodized colors!

    Learn More
    $80.00

  • Blowsion CAS Billet Aluminum One Way Valve Scupper

    Our new CAS (cool as S*%!) flow valve design prevents water getting in during tail stands, wave jumping, or all out buoy shredding. The new billet flange assembly allows use of our billet exhaust outlet so vain riders can sanitize both sides of the rear of their ski. Fits all years Yamaha Superjet, Kawasaki 650, Kawasaki 750, Kawasaki SXR 800, Polaris Octane, Rickter XFS, Rickter XFR, Rickter EVO, Rickter Edge and Most Aftermarket Hulls.

    Part Number: 06-01-022

    Learn More
    $161.50

  • Blowsion Chip Brush

    The Blowsion economy chip brush is perfect for Hydro Turf and Stitched Mat glue installations. Learn More
    $1.50

  • Blowsion Dash Fitting

    Blowsion machined aluminum dash fittings are used to recess mount rotary bilge switches and/or primer bulbs in the dash of your ski. Available in Black, Blue, Red, Green, Orange, Clear, Purple and Teal colors.

    Learn More
    $30.00

  • Blowsion Hood Bumper (3 inch)

    The Blowsion Hood Bumper is a premium solution to prevent the Handle pole from contacting the hood. For Freestyle and Freeride Applications. Black Diamond. Includes 3M Adhesive Backing.

    Part Number: 04-04-206

    Learn More
    $49.95

  • Blowsion Hood Seal

    Heavy Duty Replacement Hood Seal. Fits all years Yamaha Super Jet, Yamaha FX-1, all years Polaris Octane, Yamaha Wave Blaster and most aftermarket hulls. Dimensions: L 2.7m x W 16mm x H 19mm.

    Part Number: 04-04-411

    Learn More
    $35.95

  • Blowsion Mat Glue - Pint

    Blowsion Mat Kit Glue "Blow Goo" to the rescue. Use this solvent-based contact adhesive with your Hydro Turf or stitched mat kit and never worry again about your mats coming loose. Not water-based!

    Part Number: 06-03-141

    Learn More
    $14.95

Items 1 to 16 of 63 total

per page

Page:
  1. 1
  2. 2
  3. 3
  4. 4