Engine Performance
-
Mikuni Arm Pin Screw
Genuine Mikuni Replacement Mikuni Arm Pin Screw for Mikuni SBN Carburetors. Diagram #41.
Part Number: C6-0308-G
Learn More -
Keihin to Mikuni Carb Adapter
The adapter allows you to run a Mikuni SBN 44mm or 46mm Carburetor on your stock Kawasaki 650-750 Keihin Intake Manifold.
Part Number: ADPT-K
Learn More -
WSM Top End Rebuild Kit - Kawasaki 650
WSM Aftermarket Top End Rebuild Kit for 1986-1996 Kawasaki 650 Engines. Kit includes Pistons, Rings and Gaskets. Bore sizes available up to 76mm.
Learn More -
Blowsion Colored Hose - 1/8 inch
Finish the look of your engine compartment with Blowsion specialty colored 1/8" fuel primer hose. Available in Clear, Blue, Green, Orange, Red, Yellow, or Black. Quantity is sold by the foot.
Learn More -
Fire Power Factory Activated Sealed Battery CT16CL-B-BS(FA)
Fire Power Factory Activated Sealed Battery CT16CL-B-BS(FA). Battery comes filled and pre-charged from the manufacturer (freshening charge recommended before installation).
Part Number: 49-2253
Learn More -
RIVA Power Filter (2-Stroke)
RIVA Racing's all-new 'cone-style' flame arrestor takes a proven favorite to the next level. Reduced height accommodates low-profile hood designs of freeride standups. Stainless steel cap with integrated velocity cone increases air flow rate and efficiency providing improved throttle response. Proprietary stainless steel mesh filter element resists corrosion and is certified to meet U.S. Coast Guard 'SAE-J1928' standars for safety and reliability. Fits standard carburetor adapters and allows easy access to carburetor adjustment screws. Sold Individually.
Part Number: RY1301-1
Learn More -
Blowsion Fuel Tank Fitting
Blowsion Fuel Tank Fitting with Rubber Grommet. 1/4 Hose Barb. Compression Fit. Install with 17/32 Drill Bit.
Part Number: 01-02-598
Learn More -
3/8" Quick Disconnect / Water Restrictor
The 3/8" Quick Disconnect / Water Restrictor can be used as Quick Disconnect or use one of 3 supplied brass inserts to restrict the flow of water or increase pressure where it is needed. Includes 3 brass restrictors and stainless steel hose clamps. Now Available in all colors!
Learn More -
Mikuni Valve Body Assembly
Genuine Mikuni Replacement Valve Body Assembly for Mikuni SBN Carburetors. Assembly includes #12, #37, #38 and #39 in the diagram.
Part Number: BN44/165
Learn More -
Keihin Carb Rebuild Kit 38-44MM CDK-II
Aftermarket Keihin Carburetor Rebuild Kit for 38mm, 40mm, 42mm and 44mm CDK-II Carburetors. Fits wide range of 38-44mm Keihin™ CDK-II carbs found on PWC. Includes Viton™ tipped inlet needle.
Part Number: 01-02-492
Learn More -
Mikuni Check Valve (Clear)
Genuine Mikuni Replacement Check Valve Mikuni SBN Carburetors. Diagram #12.
Part Number: BN34/107
Learn More -
OEM Kawasaki Drive Coupler Cover
Genuine OEM Kawasaki Drive Coupler Cover. Fits all Kawasaki 750 and SXR 800 models.
Part Number: 14090-3761
Learn More -
Mikuni High Speed Washer
Genuine Mikuni Replacement High Speed Aluminum Washer for Mikuni SBN Carburetors. Diagram #21.
Part Number: BN38/39
Learn More -
ADA Cylinder Head Dome - Kawasaki 650
ADA Racing Billet Cylinder Head Dome for Kawasaki 650. Includes compression (OR042) and dome top (OR020) o-rings. Squish relief is .015 inch @ 78mm with a 9.5 degree angle. These domes fit the ADA Racing 650 Cylinder Head. Domes are sold individually.
Learn More -
Mikuni SBN 46MM Carburetor
Mikuni High Performance Super BN 46mm Carburetor. Comes Complete with Extended Throttle Shaft and Choke shaft removed. Sold Each. BN46-42-8002
Part Number: 01-02-105
Learn More -
Complete Gasket Kit - Kawasaki 650 (with seals)
Aftermarket Complete Gasket Kit for Kawasaki 650 Engines. Fits Kawasaki X2, 650SX, Jetmate, TS and SC 650 Models.
Part Number: 01-03-316
Learn More